Electronics Forum | Tue May 26 15:27:36 EDT 1998 | Dave F
| | | I'm reviewing my board fab spec. It calls for a minimum SnPb thickness of 50 microinches on HASL PWB's. I've looked at other specs that call out anything from 30 to 80 microinches, and others that just say the copper pad must be covered and s
Electronics Forum | Thu Mar 02 16:06:32 EST 2000 | eLDON sANDERS
Gentlemen, I too have been atacked by that "soldering to gold" and will add my 2 cents. I also had parts that would pop off the board when the fillet looked perfect. After lots of pain, experimentation, and sleepless nights, I solved it through a
Electronics Forum | Thu Mar 02 16:06:32 EST 2000 | eLDON sANDERS
Gentlemen, I too have been atacked by that "soldering to gold" and will add my 2 cents. I also had parts that would pop off the board when the fillet looked perfect. After lots of pain, experimentation, and sleepless nights, I solved it through a
Electronics Forum | Mon Sep 17 05:48:10 EDT 2012 | stivais
Hi Ben, Yes, this could be the reason but have you ever seen solderability issues for (new) boards with LF-HAL surface finish? I have seen this only if there are surface finish quality issues for bare boards (exposed copper etc.). In this case we di
Electronics Forum | Wed Mar 14 09:07:34 EST 2001 | blnorman
We just ran a study to try to determine this. We exposed the paste to 85% humidity to simulate worst case manufacturing. At various times we removed the paste from the chamber and tested it for tack, solder balling, wetting (copper coupon), and vis
Electronics Forum | Tue Dec 01 07:54:49 EST 1998 | kallol chakraborty
| | Hi folks , | | Lately we are seeing a lot of rawcards with black spots on the pads - most of them have Au finish(immersion gold) . We did a lot of inspecton after wave solder and found that only (fine pitch) QFP are affected the most. Our inspec
Electronics Forum | Tue Dec 01 07:24:44 EST 1998 | Earl Moon
| Hi folks , | Lately we are seeing a lot of rawcards with black spots on the pads - most of them have Au finish(immersion gold) . We did a lot of inspecton after wave solder and found that only (fine pitch) QFP are affected the most. Our inspection
Electronics Forum | Mon Aug 27 15:06:29 EDT 2001 | davef
This otta push Wolfgang over the top ... Recommended reading G.G. Harman, Wire Bonding in Microelectronics : Materials, Processes, Reliability, and Yield, 2nd edition, McGraw-Hill Electronic Packaging and Interconnection Series, 1997. G.G. Harman, R
Electronics Forum | Tue Dec 01 09:02:18 EST 1998 | Earl Moon
| | | Hi folks , | | | Lately we are seeing a lot of rawcards with black spots on the pads - most of them have Au finish(immersion gold) . We did a lot of inspecton after wave solder and found that only (fine pitch) QFP are affected the most. Our in
Electronics Forum | Fri Dec 04 20:26:34 EST 1998 | kallol Chakraborty
| | | | Hi folks , | | | | Lately we are seeing a lot of rawcards with black spots on the pads - most of them have Au finish(immersion gold) . We did a lot of inspecton after wave solder and found that only (fine pitch) QFP are affected the most. Ou
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
